Aruba Networks AP-214 Dual 3x3:3 Radio Antenna Connector Wireless Access Point APIN0214.
Aruba Model Name: AP-214
Aruba Model Number: APIN0214
Compatible Part Numbers: AP-214-F1 JW169A
Unique benefits
Wi-Fi client optimization
• 210 Series APs feature patented ClientMatch
technology to eliminate sticky client behavior while
users roam. ClientMatch continuously gathers session
performance metrics from mobile devices.
• If a mobile device moves away from an AP or if RF
interference impedes performance, ClientMatch
automatically steers the device to a better AP.
Advanced Cellular Coexistence (ACC)
• ACC lets WLANs perform at peak efficiency by
minimizing interference from 3G/4G LTE networks,
distributed antenna systems and commercial small
cell/femtocell equipment.
Quality of service for unified communication apps
• 210 Series APs support priority handling and
policy enforcement for unified communication
apps, including Microsoft Lync with encrypted
videoconferencing, voice, chat and desktop sharing.
Choose your operating mode
210 Series APs offer a choice of operating modes to meet
your unique management and deployment requirements.
• Controller-managed AP or Remote AP (RAP)
running AOS. When managed by Dell Networking
W-Series controllers, 210 Series APs offer centralized
configuration, data encryption, policy enforcement and
network services, as well as distributed and centralized
traffic forwarding. Please refer to the controller data
sheets for more details.
• Instant AP running InstantOS. In Instant mode, a single
AP automatically distributes the network configuration
to other Instant APs in the WLAN. Simply power-up
an Instant AP, configure it over the air, and plug in the
other APs – the entire process takes about five minutes.
Specifications:
• AP type: Indoor, dual radio, 5 GHz 802.11ac and 2.4 GHz
802.11n 3x3:3
• Software-configurable dual radio supports 5 GHz (Radio 0)
and 2.4 GHz (Radio 1)
• 3x3 MIMO with three spatial streams and up to 1.3 Gbps
wireless data rate
• Support for up to 256 associated client devices per radio,
and up to 16 BSSIDs per radio
• Supported frequency bands (country-specific
restrictions apply):
- 2.4000 GHz to 2.4835 GHz
- 5.150 GHz to 5.250 GHz
- 5.250 GHz to 5.350GHz
- 5.470 GHz to 5.725GHz
- 5.725 GHz to 5.850GHz
• Available channels: Dependent on configured
regulatory domain
• Dynamic frequency selection (DFS) optimizes the use of
available RF spectrum
• Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division
multiplexing (OFDM)
• Supported modulation types:
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
• Transmit power: Configurable in increments of 0.5 dBm
• Maximum (aggregate, conducted total) transmit power
(limited by local regulatory requirements):
- 2.4-GHz band: +23 dBm (18 dBm per chain)
- 5-GHz band: +23 dBm (18 dBm per chain)
- Note: conducted transmit power levels exclude antenna
gain. For total (EIRP) transmit power, add antenna gain
• Advanced Cellular Coexistence (ACC) minimizes
interference from cellular networks
• Maximum ratio combining (MRC) for improved
receiver performance
• Cyclic delay/shift diversity (CDD/CSD) for improved
downlink RF performance
• Short guard interval for 20-MHz, 40-MHz and
80-MHz channels
• Space-time block coding (STBC) for increased range and
improved reception
• Low-density parity check (LDPC) for high-efficiency error
correction and increased throughput
• Transmit beamforming (TxBF) for increased signal
reliability and range
• Supported data rates (Mbps):
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 450 (MCS0 to MCS23)
- 802.11ac: 6.5 to 1,300 (MCS0 to MCS9, NSS = 1 to 3)
• 802.11n high-throughput (HT) support: HT 20/40
• 802.11ac very high throughput (VHT) support: VHT 20/40/80
• 802.11n/ac packet aggregation: A-MPDU, A-MSDU
